Seit längerem versuche ich – bis jetzt leider total erfolglos – auf mein Garmin etrex Legend Hcx Karten zu laden. So langsam bin ich am verzweifeln….
Ich habe mich u.a. an der OSM Karte von Computerteddy versucht.
Karte runtergeladen
Auf uSD-Karte den Ordner Garmin angelegt
Runtergeladene Karte entpackt und auf SD kopiert
In „gmapsupp.img“ umbenannt
SD in Garmin gesteckt und neu gestartet
Unter Karteneinstellungen ist keine Karte auswählbar (bzw. es ist nur die “normale” Garmin Standartkarte sichtbar)
Beim neu starten des etrex sieht man im unteren Displaybereich einen „Balken“. Es sieht so aus, als würde irgendetwas (vielleicht die Karte) geladen werden. Dieses “laden” erfolgt nur wenn die uSD gesteckt ist.
Habe bereits schon viele Forumlösungen ausprobiert - ohne Erfolg.
Liebe „Experten“ ich dachte immer dass ich keine 2 linken Hände im Bereich Technik hätte. Vielleicht muß ich ja noch irgendwo, irgend etwas machen/auswählen/bestätigen … ???
As it should be done
Download the Mapsource file on your PC
Run the exe file (Make sure the data end up in the Garmin map, usually not the one which is the default)
open Mapsource
select the map (there should now be a map called OSM routable)
zoom out to you have the full map on your screen
with the knob map (Select map) select all tiles
connect your Etrex
upload the maps to the etrex
should now be available on your system
shorter but you need to know better what you do
down load the gmapsupp.zip
unzip
connect the Garmin
create folder called Garmin on the drive
copy the gmapsupp.img to this folder
In both cases you can verify the existence by: selecting map set-up on your Garmin, go to info, it should say OSM World Routable, etc.
Wichtig ist an dieser Stelle, dass du die fertige Kartendatei im Garmin-Format (*.img) herunterlädst und nicht Kartendateien für den Einsatz in Mapsource o.ä. - aus letzteren musst du erst in Mapsource eine gmapsupp.img erzeugen, die du dann auf die SD kopieren kannst.
The important bit is to use EITHER ready-to-use Garmin map (*.img) OR the respective file(s) for use in Mapsource etc.
Only the gmapsupp.img can be used if you copied it to \garmin on your device - with all others you need to create the gmapsupp.img in Mapsource first.
It will never reach 100% as the progress bar isn’t updated when the work is completed. Most of the time I do not see higher percentages than the ones you have seen.
I once had a very trivial error, which took me a while to figure out: It turned out that I was compressing the downloaded file instead of decompressing it. Of course the resulting gmapsupp.img did not work. So I finally ended up with a very simple command line that works fine for me now:
It downloads the newest map, sends it to bunzip2 to unzip it and save it onto the SD card. It works using Linux or Windows, provided you have wget and bunzip2 installed, and give it the correct path to the Garmin folder on your SD card. If you prefer to keep the zipped file, you can also try:
I’d rather suggest to use 7-zip when working with Windows - it’s free and way easier to use than any command line tools…
But back to Hadmut’s problem: on my Vista HCx w/ 3.10 the progress bar always reaches 100% during startup…
As a Vista owner I don’t know about the peculiarities of the Venture, but the Vista just starts without ever mentioning that it found an OSM map on the card. The only point to tell is in the map menu (and if you see details where the default Garmin map doesn’t have anything)