а как их(скрины)найти там,в группе в телеге ?
Ну давай я ещё выложу. Скажи там что-нибудь чтобы я понял кто ты.
увидел,спасибо!да,они задействованы меньше,но задействованы.а у меня они просто видятся,даже не отслеживаются!!написал в моторолу второй раз по этому вопросу.в первый раз(в гонконге)мне ответили что"скорее всего ,так как я задумал(т.е.чтобы эти спутники на второй частоте отслеживались и т.д.)работать не будет,т.к. телефон сделан для Гонконга ,а работает в Украине!
щас вроде поумней девушка отписывается,т.к. такого не пишет.пока жду ответа.как ответят - тут отпишусь
Расшифровываем скриншоты, в принципе всё это уже написано выше.
Те спутники, что перечислены в списке и отображены на Skyplot это те спутники, которые теоретически должны быть видны в вашем регионе, базируясь на знании текущих координат и альманахе. Спутники могут быть при этом закрыты зданиями, деревьями и т.д. и от них не будет никакого сигнала.
В вашем случае от некоторых спутников виден сигнал на частоте L1, но от них нет никакого сигнала на L5. А значит либо этот диапазон вообще не предусмотрен в антенне/радиотракте, либо действительно заблокировано слежение на уровне прошивки.
На Геодезисте там ещё ринекс выложен был
https://geodesist.ru/threads/kak-mozhno-uluchshit-tochnost-gps-v-telefone.78225/page-2#post-984000
Если это запись на открытом месте, то IMHO там ловить особо нечего, для L5/E5 только какие-то единичные отметки.
C Рождеством Христовым!!
Уважаемые Vascom , Sergey Astakhov и chnav !
ждал ответа от Моторолы ,но подумав ,понял что это ожидание не имеет смысла!
потому что Моторола сама просто не реализовала поддержку второй частоты(тел.- бюджетка)!я не знаю как эта поддержка должна выглядеть в телефоне(может антенна или драйвер или ещё чего),но одно знаю точно:самому эту поддержку не реализовать точно!
Всем отозвавшимся - спасибо!
моторола почти подтвердила вот этот вариант.почти…они же прямо не могли сказать ,что из за цены телефона посчитали излишним реализовывать поддержку всех возможностей чипсета!!
на 4pda бродил по форуму и нашел видимо ваш старый пост в теме о внешнем gps- модуле(https://4pda.ru/forum/index.php?showtopic=16685&view=findpost&p=52233427)…и подумалось :а есть ли внешние(блютуз или юсб - интерфейс)gps - модули с поддержкой L5-E5 ?
а если даже не двухчастотный ,а просто с возможностью вывода сырых данных(ринекса) ?
может можно было бы его вставить в телефон с OTG (или по блютусу)и снять данные с него,а не со встроенного жпс модуля ?
на плате ublox7 недорогой видел в продаже(к примеру!!) или можно новее что-то найти ?
хочется но телефоне точности до метра…
Есть, ublox даже выпустил приложение в сторе, чтобы читать данные со своих устройств. Но точность в метр без базовых станций не достижим.
день добрый!
рутанул моторолу и вытащил два файла gps.conf и gps_debug.conf.
попробую их тут вставить.может гляньте на досуге - почему вторая частота не применяется при расчёте местоположения!!
#hardware/qcom/gps/loc_api/conf/gps.conf
NI_SUPL_DENY_ON_NFW_LOCKED = 1
#####################################
proxyAppPackageName
#####################################
This is a string that is sent to the framework
in nfwNotifyCb callback
Add NFW package name
PROXY_APP_PACKAGE_NAME = com.motorola.nfwlocationattribution
#Version check for XTRA
#DISABLE = 0
#AUTO = 1
#XTRA2 = 2
#XTRA3 = 3
XTRA_VERSION_CHECK=0
Error Estimate
_SET = 1
_CLEAR = 0
ERR_ESTIMATE=0
#NTP server
NTP_SERVER=time.izatcloud.net
#XTRA CA path
XTRA_CA_PATH=/usr/lib/ssl/certs
DEBUG LEVELS: 0 - none, 1 - Error, 2 - Warning, 3 - Info
4 - Debug, 5 - Verbose
If DEBUG_LEVEL is commented, Android’s logging levels will be used
DEBUG_LEVEL = 2
Intermediate position report, 1=enable, 0=disable
#INTERMEDIATE_POS=0
supl version 1.0
#SUPL_VER=0x10000
Emergency SUPL, 1=enable, 0=disable
#SUPL_ES=1
#Choose PDN for Emergency SUPL
#1 - Use emergency PDN
#0 - Use regular SUPL PDN for Emergency SUPL
#USE_EMERGENCY_PDN_FOR_EMERGENCY_SUPL=0
#SUPL_MODE is a bit mask set in config.xml per carrier by default.
#If it is uncommented here, this value will overwrite the value from
#config.xml.
#MSA=0X2
#MSB=0X1
#SUPL_MODE=
GPS Capabilities bit mask
SCHEDULING = 0x01
MSB = 0x02
MSA = 0x04
ON_DEMAND_TIME = 0x10
default = ON_DEMAND_TIME | MSA | MSB | SCHEDULING
CAPABILITIES=0x77
Accuracy threshold for intermediate positions
less accurate positions are ignored, 0 for passing all positions
ACCURACY_THRES=5000
################################
AGPS server settings
################################
FOR SUPL SUPPORT, set the following
SUPL_HOST=supl.host.com or IP
SUPL_PORT=1234
FOR MO SUPL SUPPORT, set the following
MO_SUPL_HOST=supl.host.com or IP
MO_SUPL_PORT=1234
FOR C2K PDE SUPPORT, set the following
C2K_HOST=c2k.pde.com or IP
C2K_PORT=1234
Bitmask of slots that are available
for write/install to, where 1s indicate writable,
and the default value is 0 where no slots
are writable. For example, AGPS_CERT_WRITABLE_MASK
of b1000001010 makes 3 slots available
and the remaining 7 slots unwritable.
#AGPS_CERT_WRITABLE_MASK=0
####################################
LTE Positioning Profile Settings
####################################
0: Enable RRLP on LTE(Default)
1: Enable LPP_User_Plane on LTE
2: Enable CP LPP, UP RRLP
3: Enable both LPP_User_Plane and LPP_Control_Plane
4: Enable CP LPP and LPPe DBH, UP RRLP (TMO)
5: Enable CP & UP - LPP and LPPe DBH (VzW)
6: Enable CP LPP and LPPe DBH, LPPe WLAN, UP RRLP (TMO)
7: Enable CP & UP - LPP and LPPe DBH, LPPe WLAN (VzW)
8: Enable CP LPP and LPPe DBH, LPPe WLAN, LPPe UBP, UP RRLP (TMO)
9: Enable CP & UP - LPP and LPPe DBH, LPPe WLAN, LPPe UBP(VzW)
10: Enable CP LPP and LPPe DBH, UP LPP - disable UP LPPe(AT&T )
11: Enable CP LPP and LPPe DBH/WLAN, UP LPP - disable UP LPPe (AT&T)
12: Enable CP LPP and LPPe DBH/WLAN/UBP, UP LPP - disable UP LPPe (AT&T)
#LPP_PROFILE = 2
####################################
#Datum Type
####################################
0: WGS-84
1: PZ-90
#DATUM_TYPE = 0
################################
EXTRA SETTINGS
################################
NMEA provider (1=Modem Processor, 0=Application Processor)
#NMEA_PROVIDER=0
Mark if it is a SGLTE target (1=SGLTE, 0=nonSGLTE)
#SGLTE_TARGET=0
##################################################
Select Positioning Protocol on A-GLONASS system
##################################################
0x1: RRC CPlane
0x2: RRLP UPlane
0x4: LLP Uplane
#A_GLONASS_POS_PROTOCOL_SELECT = 0
##################################################
Select technology for LPPe Control Plane
##################################################
0x1: DBH for LPPe CP
0x2: WLAN AP Measurements for LPPe CP
0x4: SRN AP measurement for CP
0x8: Sensor Barometer Measurement LPPe CP
#LPPE_CP_TECHNOLOGY = 0
##################################################
Select technology for LPPe User Plane
##################################################
0x1: DBH for LPPe UP
0x2: WLAN AP Measurements for LPPe UP
0x4: SRN AP measurement for UP
0x8: Sensor Barometer Measurement LPPe UP
#LPPE_UP_TECHNOLOGY = 0
##################################################
AGPS_CONFIG_INJECT
##################################################
enable/disable injection of AGPS configurations:
SUPL_VER
SUPL_HOST
SUPL_PORT
MO_SUPL_HOST
MO_SUPL_PORT
C2K_HOST
C2K_PORT
LPP_PROFILE
A_GLONASS_POS_PROTOCOL_SELECT
0: disable
1: enable
#AGPS_CONFIG_INJECT = 1
##################################################
GNSS settings for automotive use cases
Configurations in following section are
specific to automotive use cases, others
please do not change, keep the default values
##################################################
AP Coarse Timestamp Uncertainty
##################################################
default : 10
AP time stamp uncertainty, until GNSS receiver
is able to acquire better timing information
#AP_TIMESTAMP_UNCERTAINTY = 10
##################################################
QDR engine availability status
##################################################
0 : NO QDR (default)
1 : QDR enabled
This settings enables QDR Configuration for
automotive use case, if enabled then
DR_AP_Service needs to be enabled in izat.conf
#EXTERNAL_DR_ENABLED = 0
#####################################
DR_SYNC Pulse Availability
#####################################
0 : DR_SYNC pulse not available (default)
1 : DR_SYNC pulse available
This configuration enables the driver to make use
of PPS events generated by DR_SYNC pulse
Standard Linux PPS driver needs to be enabled
#DR_SYNC_ENABLED = 0
#####################################
PPS Device name
#####################################
#PPS_DEVICENAME = /dev/pps0
#####################################
Ignore PPS at Startup and after long outage
#####################################
#IGNORE_PPS_PULSE_COUNT = 1
#####################################
Long GNSS RF outage in seconds
#####################################
#GNSS_OUTAGE_DURATION = 10
#####################################
AP Clock Accuracy
#####################################
Quality of APPS processor clock (in PPM).
Value specified is used for calculation of
APPS time stamp uncertainty
#AP_CLOCK_PPM = 100
#####################################
MAX ms difference to detect missing pulse
#####################################
Specifies time threshold in ms to validate any missing PPS pulses
#MISSING_PULSE_TIME_DELTA = 900
#####################################
Propagation time uncertainty
#####################################
This settings enables time uncertainty propagation
logic incase of missing PPS pulse
#PROPAGATION_TIME_UNCERTAINTY = 1
#######################################
APN / IP Type Configuration
APN and IP Type to use for setting
up WWAN call.
Use below values for IP Type:
v4 = 4
v6 = 6
v4v6 = 10
#######################################
INTERNET_APN = abc.xyz
INTERNET_IP_TYPE = 4
SUPL_APN = abc.xyz
SUPL_IP_TYPE = 4
#####################################
Modem type
#####################################
This setting configures modem type
(external=0 or internal=1)
comment out the next line to vote
for the first modem in the list
MODEM_TYPE = 1
##################################################
CONSTRAINED TIME UNCERTAINTY MODE
##################################################
0 : disabled (default)
1 : enabled
This setting enables GPS engine to keep its time
uncertainty below the specified constraint
#CONSTRAINED_TIME_UNCERTAINTY_ENABLED = 0
If constrained time uncertainty mode is enabled,
this setting specifies the time uncertainty
threshold that gps engine need to maintain.
In unit of milli-seconds.
Default is 0.0 meaning that modem default value
of time uncertainty threshold will be used.
#CONSTRAINED_TIME_UNCERTAINTY_THRESHOLD = 0.0
If constrained time uncertainty mode is enabled,
this setting specifies the power budget that
gps engine is allowed to spend to maintain the time
uncertainty.
Default is 0 meaning that GPS engine is not constained
by power budget and can spend as much power as needed.
In unit of 0.1 milli watt second.
#CONSTRAINED_TIME_UNCERTAINTY_ENERGY_BUDGET = 0
##################################################
POSITION ASSISTED CLOCK ESTIMATOR
##################################################
0 : disabled (default)
1 : enabled
This setting enables GPS engine to estimate clock
bias and drift when the signal from at least 1
SV is available and the UE’s position is known by
other position engines.
#POSITION_ASSISTED_CLOCK_ESTIMATOR_ENABLED = 0
#####################################
CP_MTLR_ES
#####################################
CP MTLR ES, 1=enable, 0=disable
#CP_MTLR_ES=0
##################################################
GNSS_DEPLOYMENT
##################################################
0 : Enable QTI GNSS (default)
1 : Enable QCSR SS5
This setting use to select between QTI GNSS
and QCSR SS5 hardware receiver.
By default QTI GNSS receiver is enabled.
GNSS_DEPLOYMENT = 0
и второй файл
Sample file for use for on device debug override only
Prefer frameworks/base/core/res/res/values/config.xml and
frameworks/base/core/res/res/values-mcc*-mnc*/config.xml
################################
AGPS server settings
################################
FOR SUPL SUPPORT, set the following
SUPL_HOST=supl.google.com or IP
SUPL_PORT=7275
supl version 2.0
SUPL_VER=0x20000
#SUPL_MODE is a bit mask set in config.xml per carrier by default.
#If it is uncommented here, this value will overwrite the value from
#config.xml.
#MSA=0X2
#MSB=0X1
#SUPL_MODE=1
Emergency SUPL, 1=enable, 0=disable
#SUPL_ES=0
#Choose PDN for Emergency SUPL
#1 - Use emergency PDN
#0 - Use regular SUPL PDN for Emergency SUPL
#USE_EMERGENCY_PDN_FOR_EMERGENCY_SUPL=0
####################################
LTE Positioning Profile Settings
####################################
0: Enable RRLP on LTE(Default)
1: Enable LPP_User_Plane on LTE
2: Enable LPP_Control_Plane
3: Enable both LPP_User_Plane and LPP_Control_Plane
#LPP_PROFILE = 2
##################################################
Select Positioning Protocol on A-GLONASS system
##################################################
0x1: RRC CPlane
0x2: RRLP UPlane
0x4: LLP Uplane
#A_GLONASS_POS_PROTOCOL_SELECT = 0
Below bit mask configures how GPS functionalities
should be locked when user turns off GPS on Settings
Set bit 0x1 if MO GPS functionalities are to be locked
Set bit 0x2 if NI GPS functionalities are to be locked
default - non is locked for backward compatibility
#GPS_LOCK = 0
конечно надежды нету…включить вторую частоту.но для общего развития
Есть, ublox даже выпустил приложение в сторе, чтобы читать данные со своих устройств. Но точность в метр без базовых станций не достижим.
говоря за базовіе станции вы имеете ввиду геодезические кастеры с доступом по NTRIP?
или второе усторойство ,которое используется как база?
или и то и то совместно ?
если есть возможность - поясните более развернуто или ссылочку где почитать!
добрый вечер!!
поставил гугловскую программу GNSS Analysis tools,для интереса - посмотреть что там анализируется и т.д.
и вот при попытке запуска ее терминал начинает ругаться!
а на что именно - не понимаю.помогите разобраться пожалуйста,если можете,конечно!!!
https://postimg.cc/0KbFqmjF
Не может найти библиотеку libmwlaunchermain.so
предположим я ее нашел.а куда ее надо вставить?
в эти папки(которые разделяются двоеточием - не подошло,ничего не меняется
несколько путей на скрине(4 шт) я вставил во все эту библиотеку
Можно попробовать положить в тот каталог откуда запускаешь.
спасибо за совет!но попробую только завтра.
хоть бы заработало…
Можно попробовать положить в тот каталог откуда запускаешь.
In the following directions, replace MR/v94 by the directory on the target machine where MATLAB is installed, or MR by the directory where the MATLAB Runtime is installed.
(1) Set the environment variable XAPPLRESDIR to this value:
MR/v94/X11/app-defaults
(2) If the environment variable LD_LIBRARY_PATH is undefined, set it to the following:
MR/v94/runtime/glnxa64:MR/v94/bin/glnxa64:MR/v94/sys/os/glnxa64:MR/v94/sys/opengl/lib/glnxa64
If it is defined, set it to the following:
${LD_LIBRARY_PATH}:MR/v94/runtime/glnxa64:MR/v94/bin/glnxa64:MR/v94/sys/os/glnxa64:MR/v94/sys/opengl/lib/glnxa64
Linux Installation:
Install MATLAB Runtime in a writable directory,
then run the application from the Terminal, like this:
$ cd ~/Desktop/GnssAnalysisFiles/application
$ ./run_GnssAnalysisApp.sh [mcr_directory]
[mcr_directory] is the directory where MATLAB Runtime was installed
e.g. ~/MATLAB/MATLAB_Runtime/v94/
(these instructions are also in for_redistribution_files_only/readme_instructions_linux.txt)
Это что?
Ломать олаза о транслит неохота.
У меня на том компе,где стоит эта гкгловская программа ,нету русского.
А эта инструкция по установке и запуску этой тулзы.но я ее не понимаю,через переводчик бред переводится.вы не понимаете что оно хочет?
вы не понимаете что оно хочет?
(2) If the environment variable LD_LIBRARY_PATH is undefined
echo $LD_LIBRARY_PATH